Turn any photo into a one colour stencil

Every pixel goes to solid ink or bare paper, so a portrait becomes bold shapes you can cut, spray or screen print. One hard threshold, no AI, nothing uploaded.

Open the editor with this effect

What you get

Made with plain math, not a model

There is no generative model behind this look and nothing was trained on anyone's work. It is a short list of fixed steps running in your browser.

  1. Read the photo: Your photo is read pixel by pixel inside your browser. It is never uploaded, so nothing leaves your device.
  2. Dither: Each pixel is rounded to the nearest available ink, and the leftover error is passed to its neighbours or checked against a fixed pattern, so the overall tone survives.
  3. Same input, same pixels: Every step is fixed math with fixed seeds. Run it again tomorrow on the same photo and you get exactly the same image.

A stencil is a sheet with holes in it. Paint goes through the holes and stops everywhere else, so every part of the design is either full colour or nothing. That is why a good stencil starts with a photo cut down to two tones, and why getting that cut right matters more than any filter. Bitgrain does it with a single threshold on your own photo, in your browser, with no AI involved.

How stencils work

Stencils are cut from card, acetate or thin plastic film such as Mylar. Film lasts longer and can be cleaned and reused, card is cheap and easy to cut with a craft knife.

The cut out areas print and the solid areas block. Most portrait stencils print the shadows, so the dark parts of the face are what you cut away.

Enclosed shapes are the classic problem. The middle of a letter O, or an eye surrounded by shadow, falls out when you cut around it. Stencil makers leave thin strips called bridges to hold those islands in place, or they redraw the shape so it connects to the rest.

Street artists made the photo stencil famous from the early 1980s onwards, with Blek le Rat in Paris often credited as an early pioneer. The same idea sits under screen printing, where the stencil is held on a mesh.

Getting a clean one layer stencil from a photo

Everything depends on where the threshold falls. Too low and the face disappears into paper, too high and it fills in with black. Move it until the eyes, nose and mouth each have a clear shape.

Photos with strong side light work best. Half the face in shadow and half in light gives the classic stencil portrait. Flat front light gives you a few floating features and not much else.

Small specks are hard to cut and paint badly. Look for tiny islands of black or white and either tidy them in an editor or nudge the brightness until they merge into larger shapes.

Check every island before you cut. Anything that is not connected to the rest of the sheet needs a bridge.

Two and three layer stencils

For more depth, artists cut one stencil per tone and spray them in order, usually lightest first and darkest last. Three layers, for light, mid and dark, is a common setup.

To plan the layers, posterise the photo to three or four levels. Each flat band of grey becomes one stencil.

Add registration marks in the corners of every layer so they line up when you spray. Even a few millimetres of drift shows on a face.

How to do it in Bitgrain

Open the editor from this page. The sample is already cut to a one colour stencil with the Threshold dither. Drop in your own photo.

Use Brightness in the Tone panel to move the cut, and Contrast to sharpen the edges between shapes.

For a multi layer plan, add Posterise from Effects and set Levels to three or four.

Export a PNG at full size and print it, or trace it into vectors in a tool like Inkscape if your cutting machine needs a vector file.

Common questions

Can I use the PNG with a Cricut or a laser cutter?

Most cutting machines want a vector outline. Export the PNG from Bitgrain, then trace it to SVG in a vector tool before sending it to the machine.

Why do some parts of my stencil fall out?

Those are islands, shapes fully surrounded by cut areas. Add thin bridges to connect them to the rest of the sheet before cutting.

Is my photo uploaded or processed by AI?

Neither. The threshold runs in your browser and the photo stays on your device.

Related tools